After receiving my laptop from motherboard change (I put the same model), this message appears only if I try to run some demanding program, e.g., an installation.

Notice that my computer even with the old motherboard used to work perfectly and fast.

(Intel Mobile 760, 512RAM, 80GB, NVidia GeForce 6600 128MB (dedicated), Windows XP Pro, are the specifications of my PC.)

Anyone, please help, otherwise I'm gonna shoot the PC technician and make a new song "I shoot the Technician"

The further details of the error are the following
0xC0000185
0xC0000185
0xC0000000
0x015BD000

what company did you buy it from? How Long have the problems existed with this same laptop. Try using this website to see if there is anything that deals with the Hex Code addresses http://www.aumha.org/win5/kbestop.htm

It is a built-to-order laptop, basically I don't now the manufacturer, but the name is Innovator.
The problem happens a few days now, after the change of the motherboard

try this one:
http://www.winhelpline.info/forum/faq-datenbank-bekannte-fehle...error.html

woops, sorry, forgot that I am probably the only one who speaks german around here

Put the german text into a translator, so it's probably got some horrible english in there: (hope it helps anyway)

If you implement Windows 2000 or Windows NT, one of the following error messages is possibly indicated: Stop 0x00000077 KERNEL_STACK_INPAGE_ERROR In this article the problem treatment for these error messages is described. A cause: This problem can occur, if a requested side with Kerneldaten cannot be read from the paging file into the main memory or the master boat data record is infected with a virus. If you liked to determine the possible reason, you must analyze the error message exactly. If first and the third parameter are zero, the four parameters are defined as follows: 1. 0 (zero) 2nd PSE value (PAGE Table error) at the time of the error 3rd 0 (zero) 4th address of the signature on the Kernelstapel First or the third parameter is not zero, the following definitions apply: 1. Status code 2nd I/O status code 3rd number of the paging file 4th offset in paging file If this is the case, the cause of the problem can be determined over the second parameter (the I/O status code) assistance of the following information. These information is in the format: "value of the second parameter" followed specified of a "general cause": 0xC000009A, or STATUS_INSUFFICIENT_RESOURCES: not sufficient not-paged out pool resources 0xC000009C, or STATUS_DEVICE_DATA_ERROR: incorrect blocks on the non removable disk. 0xC000009D, or STATUS_DEVICE_NOT_CONNECTED: incorrect cable connections, missing time limitation or the CONTROLLERS is not able to access the non removable disk. 0xC000016A, or STATUS_DISK_OPERATION_FAILED: incorrect blocks on the non removable disk 0xC0000185, or STATUS_IO_DEVICE_ERROR: unsuitable time limitation or defective cable connections of the SCSI based devices and/or two devices, which try, to use the same interrupt request (IRQ). Solution: Select a suitable method, in order to solve this problem: Boat sector virus Implement a current anti-virus program, in order to determine whether the boat sector is infected with a virus and removes you the virus if necessary from your computer. No boat sector virus If you examine the system log in the event announcement for additional error messages, which help with the determination of the equipment, which causes the error. Incorrect block. "stop 0x77" is caused due to an incorrect block in a paging file or an error of the hard disk controller. In very rare cases it is released by sufficient not not-paged out pool resources. First and the second parameter are 0, the pile signature in the Kernelstapel was not found. The cause for this problem is incorrect hardware. If the I/O status is C0000185 and the paging file is on SCSI based data medium equipment, data medium cables and SCSI time limitation should be examined. If the I/O status code is Oxc000009c or 0xC000016A, this normally indicates that the data could not be read due to an incorrect block on the non removable disk. If you can again start the computer after indicating the error message, the automatic test program is implemented and tried to assign the incorrect range. If the automatic test program (Autochk) cannot examine the non removable disk for errors, start the data medium examination manually. If the computer assistance is formatted by NTFS, implement "Chkdsk /f /r" in the system partition. They must again start the computer before beginning of the Datentraegerscans. If you cannot start the computer due to this problem, implement "Chkdsk /r" over the command console. Defective or unreliable RAM is likewise a frequent cause for this kind of problem. Guarantee that all adapter maps of the computer correct fit. Examine whether the contacts of the adapter maps are clean. Deactivate the Systemcaching in the BIOS, in order to determine whether the error can be repaired thereby. If the problem is not solved thereby, it can be that the motherboard of the computer is damaged. Q228753


EDIT: whenever it says boat, it means boot